BK Precision 2510B Osciloscop portabil

Specifications

Note: All specifications apply to the unit after a temperature stabilization time of 30 minutes over an ambient temperature range of 23 °C ± 5 °C.

Model 2511B 2512B 2515B 2516B

Performance Characteristics

Bandwidth (-3B) 100 MHz 200 MHz 100 MHz 200 MHz

Real Time Sampling Rate 1 GSa/s (half-channel interleaved)(1), 500 MSa/s (per channel)

Channels 2 non-isolated 2 isolated

Rise Time (typical) < 3.5 ns < 1.7 ns < 3.5 ns < 2.0 ns

Memory Depth 12 Mpts (half-channel interleaved), 6 Mpts (per channel)

Waveform Update Rate Up to 100,000 wfms/s (normal mode), 400,000 wfms/s (sequence mode)

Ch to Ch Isolation DC to Max BW: > 40 dB

Probe Attenuation

Selectable Factors 0.1X, 0.2X 0.5X, 1X, 2X, 5X, 10X, 50X, 100X, 500X, 1000X, 2000X, 5000X, 10000X, Custom

Input Coupling AC, DC, GND

Input Impedance DC: (1 MΩ ± 2 %) || (14 pF ± 2 pF) DC: (1 MΩ ± 2 %) || (14 pF ± 2 pF)

DC Gain Accuracy ≤ ± 3 %: ≥ 10 mV/div

≤ ± 4 %: < 10 mV/div

Max. Input Voltage

CAT II 300 Vrms Between BNC Signal and Protective Earth

CAT II 30 Vrms Between BNC GND and Protective Earth

CAT II 300 Vrms Between BNC Signal and BNC GND

CAT III 600 Vrms, CAT II 1000 Vrms Between BNC Signal and Protective Earth

CAT III 600 Vrms, CAT II 1000 Vrms Between BNC GND and Protective Earth

CAT III 300 Vrms Between BNC Signal and BNC GND

Vertical System

Vertical Resolution 8 bits 8 bits

Sensitivity Range 2 mV/div to 100 V/div (1-2-5 order) 5 mV/div to 100 V/div (1-2-5 order)

Voltage Offset Range

(Probe 1x)

2 mV to 296 mV : ± 5 V

302 mV to 7.5 V : ± 80 V

7.6 V to 100 V : ± 400 V

Offset Accuracy ± (1.5% of Offset + 1.5% per division + 5 mV) ± (1.5% of Offset + 1.5% per division + 5 mV)

Bandwidth Limit 20 MHz ± 40%

Bandwidth Flatness

DC to 10% (BW): ± 1 dB

10% to 50% (BW): ± 2 dB

50% to 100% (BW): +2 dB / -3 dB

Low-Frequency Response

(AC coupling -3 dB) ≤ 2 Hz (at input BNC)

Noise/SNR

2 mV/div: > 24 dB

5 mV/div: > 25 dB

≥ 10 mV/div: > 35 dB

P-P Noise ≤ 15 SDEV Spec

SFDR Including Harmonics ≥ 30 dB ≥ 28 dB

CMRR - > 100 dB DC

> 50 dB to AC 1 MHz

Overshoot (500 ps Pulse) Typical 12% Typical 18%

Horizontal System

Horizontal Scan Range 1.0 ns/div to 100 s/div

Channel Skew < 300 ps

Timebase Accuracy ± 25 ppm

Display Format Y -T, X -Y, Roll

Roll Mode 50 ms/div to 100 s/div (1-2-5 order)

(1) Half channel operation means that only Ch 1 or Ch 2 is active.

Handheld Digital Storage Oscilloscopes

2510B Series

6 bkprecision.com

Specifications (cont.)

Acquisition System

Peak Detect 2 ns

Average Selectable from: 4, 16, 32, 64, 128, 256, 512, 1024

Enhance

Resolution (ERES) Enhance bits: 0.5, 1.5, 2, 2.5, 3

Interpolation Sin(x)/x, Linear

Trigger System

Types Edge, Slope, Pulse Width, Video, Window, Interval, Dropout, Runt, Pattern

Serial Triggers: I2C, SPI, UART, CAN, LIN

Modes Auto, Normal, Single

Level Internal: ± 4.5 div from the center of the screen

Holdoff Range 80 ns to 1.5 s

Coupling AC, DC, LF reject, HF reject

Coupling Frequency

Response

AC: Blocks DC components and attenuates signals below 8 Hz

DC: Passes all components of the signal

LFRJ: Blocks the DC component and attenuates low-frequency components below 2 MHz

HFRJ: Attenuates high-frequency components above 1.2 MHz

Accuracy (typical) Internal: ± 0.2 div

Sensitivity DC to Max BW: 0.8 div

Jitter < 100 ps

Displacement Pre-trigger: 0 to 100 % Memory

Delay Trigger: 0 to 10,000 div

Source All Channels

Waveform Measurements and Math

Source All channels, zoom, math, references, history

Number of

Measurements 4 displayed simultaneously, 5 displayed in statistics table

Measurement Range Screen or gate region

Measurement Parameters 38 Types

Vertical Max, Min, Pk-Pk, Ampl, Top, Base, Mean, Cmean, Stdev, Cstd, VRMS, Crms, FOV, FPRE, ROV, RPRE, Level@X

Horizontal Period, Freq, +Width, -Width, Rise time, Fall time, Bwid, +Duty, -Duty, Delay, Time@Level

Delay Phase, FRFR, FRFF, FFFR, FFFF, FRLR, FRLF, FFLR, FFLF, Skew

Cursors

Manual: Time X1, X2, (X1 -X2), (1/ΔT)

Voltage Y1, Y2, (Y1 -Y2)

Track: Time X1, X2, (X1 -X2)

Statistics Current, Mean, Min, Max, Stdev, Count

Counter Hardware 6-digit counter

Math Operation + , -, * , / , FFT , d/dt , ∫dt , √

FFT Window Rectangular, Blackman, Hanning, Hamming, Flattop

FFT Display Full Screen, Split, Exclusive

Cursors

Types Voltage, Time

Measurements ΔV, ΔT, 1/ΔT (frequency)

Search

Event Edge, Slope, Pulse, Interval, Runt

Event Number

Y – T: 600

Roll: No limit

Stop after roll: 600

Handheld Digital Storage Oscilloscopes

2510B Series

7 bkprecision.com

Specifications (cont.)

Model 2511B and 2512B 2515B and 2516B

Display System

Display Type 5.6” TFT LCD

Display Resolution 640 x 480 pixels

Color 24-bit

Contrast (typical) 500:1

Backlight Intensity (typical) 200 nits

Wave Display Range 8 x 12 divisions

Wave Display Mode Dots, Vector

Color Mode Normal, Color Grade

Intensity Grading 256 levels

Persistence Off, 1 sec, 5 sec, 10 sec, 30 sec, Infinite

Screen-Saver Off, 1 min, 5 min, 10 min, 30 min, 1 hr

Zoom Vertically or horizontally expand or compress a live or stopped waveform

Language English, French, Japanese, Korean, German, Spanish, Russian, Italian, Portuguese, Simplified Chinese, Traditional Chinese

I/O Interface

USB Host 1 port, isolated type A plug, full/low speed, supports USB flash drives

USB Device 1 port, micro USB-B, remote connectivity

Probe Compensation 1 kHz, 0 to 5 V square wave output

Environmental

Temperature Operating: 32 ºF to 104 ºF (0 ºC to +40 ºC)

Non-operating: 68 ºF to 140 ºF (-20 ºC to +60 ºC)

Humidity Operating: 85% RH, 104 ºF (40 ºC), 24 hours

Non-operating: 85% RH, 149 ºF (65 ºC), 24 hours

Altitude Operating: ≤ 6,561.68 ft (2000 m)

Non-operating: ≤ 16,404.2 ft (5000 m)

Electromagnetic

Compatibility Meets EMC directive (2014/30/EU), meets or exceeds IEC 61326-1:2012/EN61326-1:2013 (Basic)

Safety UL 61010-1:2012/R:2018-11; CAN/CSA-C22.2 No. 61010-1:2012/A1:2018-11. UL 61010-2-030:2018; CAN/CSAC22.2

No. 61010-2-030:2018., UL 61010-2-033:2020.

General

Power Adapter Input 100 to 240 VAC,

50/60 Hz, 1.2 A

100 to 240 VAC,

50/60 Hz, 1.1 A

Power Adapter Output 9 V, 4 A 12 V, 4 A

Operating Time (typical) 5.5 hours 4 hours

Battery Capacity 6900 mAh

Charging Protection ≥ 55 ºC at Battery

Power Consumption 9 W 11 W

IP Rating IP51

Dimensions (W x H x D) 6.61” x 10.87” x 2.68” (168 x 276 x 68 mm)

Weight (with battery) Without package: 3.86 lbs (1.75 kg)

Warranty 3 Years

Standard Accessories Power adapter, USB cable, passive probe (x2), 600 mA shunt, 10 A shunt, carrying bag, battery pack

Handheld Digital Storage Oscilloscopes

2510B Series

8 bkprecision.com

Specifications (cont.)

Serial Decoder

Decoders 2

Threshold -4.5 to 4.5 divisions

List 1 to 7 lines

I2C

Signal SCL, SDA

Address 7, 10 bits

SPI

Signal SCL, MISO, MOSI, CS indentifiers

Edge Select Rising, Falling

Idle Level Low, High

Bit Order MSB, LSB

UART

Signal Rx, Tx

Data Width 5, 6, 7, 8 bits

Parity Check None, Odd, Even, Space, Mark

Stop Bit 1, 1.5, 2 bits

Idle Level Low, High

CAN

Signal CAN_H, CAN_L

Source CAN_H, CAN_L, CAN_H - CAN_L

LIN

Specification Package

Revision Ver1.3, Ver2.0

Multimeter (DMM)

Max. Resolution 6000 counts

Max. Input Voltage 2511B, 2512B: CAT III 300 Vrms, CAT II 600 Vrms

2515B, 2516B: CAT III 600 Vrms, CAT II 1000 Vrms

Max. Voltage (shunt) CAT III 60 Vrms

Function Range Resolution Accuracy(4)

DC Voltage

60.00 mV 10 µV ± (1% + 15 digits)

600.0 mV 100 µV

± (1% + 15 digits)

6.000 V 1 mV

60.00 V 10 mV

600.0 V 100 mV

1000 V(2) 1 V ± (1% + 15 digits)

AC Voltage

(45 Hz to 400 Hz)

60.00 mV 10 µV ± (1% + 15 digits)

600.0 mV 100 µV

± (1% + 15 digits)

6.000 V 1 mV

60.00 V 10 mV

600.0 V 100 mV

750 V(2) 1 V ± (1% + 15 digits)

DC Current(3)

60.00 mA 10 µA ± (1% + 15 digits) 600.0 mA 100 µA

6.000 A 1 mA

± (1% + 15 digits) 10.00 A 10 mA

AC Current(3)

(45 Hz to 400 Hz)

60.00 mA 10 µA ± (1% + 15 digits) 600.0 mA 100 µA

6.000 A 1 mA

± (1% + 15 digits) 10.00 A 10 mA

Resistance

600.0 Ω 0.1 Ω

± (1% + 15 digits)

6.000 kΩ 1 Ω

60.00 kΩ 10 Ω

600.0 kΩ 100 Ω

6.000 MΩ 1 kΩ

60.00 MΩ 10 kΩ

Capacitance

40.00 nF 10 pF ± (1% + 15 digits)

400.0 nF 100 pF

± (1% + 15 digits)

4.000 nF 1 nF

40.00 µF 10 nF

400.0 µF 100 nF

Diode 0 to 2 V

Continuity < 50 Ω alarm

Data Logging

Scope Recorder (Sample Logger)

Source CH1, CH2, CH1 & CH2

Sample Rate 1 Sa/s to 25 kSa/s (1-2-5 order)

Memory Depth 50 MB internal, supports up to 2 GB external memory

Log Time

(max. sampling)

Approx. 23 min in single-channel mode,

11 min in two channels mode with internal memory

Approx. 22 hours in single-channel mode,11 hours in

two-channel mode with external memory

Data Format Binary

Trend plot (Measurement Logger)

Source Oscilloscope or Meter input

Log Interval 0.1 s to 10 min

Simultaneous Logging 4 plots max

Memory

Depth

Approximately 3.6 Msamples in single-channel mode,

900 ksamples in four-channel mode

Log Time(min. interval) Approximately 100 hours

Data Format Binary

Exportable Format Binary, CSV, MATLAB

(2) Applies to 2515B/2516B only

(3) For 10 A range, measurement time should not exceed 10 seconds. Interval time 15 minutes

(4) Accuracy is based on ± (% of reading + offset)

Handheld Digital Storage Oscilloscopes

2510B Series

9 v030424 bkprecision.com

Specifications (cont.)

Serial Decode Trigger

I

2

C Trigger

Condition Start, Stop, Restart, No Ack, EEPROM, 7 bits Address

& Data, 10 bits Address & Data, Data Length

Data Format Hex

Limit Range EEPROM: =, >, <

Data Length

EEPROM: 1 byte

Addr & Data: 1 to 2 byte

Data Length: 1 to 12 byte

R/W Bit Addr & Data: Read, Write, Don’t care

SPI Trigger

Condition Data

Data Format Binary

Data Length 4 to 96 bits

Bit Value 0, 1, X

Bit Order LSB, MSB

UART Trigger

Condition Start, Stop, Data, Parity Error

Data Format Hex

Limit Range =, >, <

Data Length 1 byte

Data Width 5, 6, 7, 8 bits

Parity Check None, Odd, Even, Space, Mark

Stop bit 1, 1.5, 2 bits

Idle Level High, Low

Baud Rate (Selectable) 600, 1200, 2400, 4800, 9600, 19200,38400, 57600,

115200, Custom bit/s

Baud Rate (Custom) 300 to 5,000,000 bit/s

CAN Trigger

Condition Start, Remote, ID, ID + Data, Error

ID STD (11 bits), EXT (29 bits)

Data Format Hex

Data Length 1 to 2 byte

Baud Rate 5k, 10k, 20k, 50k, 100k, 125k, 250k, 500k, 800k, 1M,

Custom bit/s

LIN Trigger

Condition Break, Frame ID, ID + Data, Error

ID 1 byte

Data Format Hex

Data Length 1 to 2 byte

Baud Rate (Selectable) 600/1200/2400/4800/9600/19200/Custom bit/s

Baud Rate (Custom) 300 bit/s to 20 Mbit/s

Trigger Types

Edge Trigger

Slope Rising, Falling, Alternating (Rising & Falling)

Slope Trigger

Slope Rising, Falling

Limit Range < , >, < >, > <

Time Range 2 ns to 4.2 ns

Resolution 1 ns

Pulse Width Trigger

Polarity +width, -width

Limit Range < , >, < >, > <

Time Range 2 ns to 4.2 ns

Resolution 1 ns

Video Trigger

Signal Standard NTSC, PAL, 720p/50, 720p/60,

1080p/50,1080p/60,1080i/50,1080i/60, Custom

Sync Any, Select

Condition Line, Field

Window Trigger

Type Absolute, Relative

Interval Trigger

Slope Rising, Falling

Limit Range < , >, < >, > <

Time Range 2 ns to 4.2 ns

Resolution 1 ns

Dropout Trigger

Timeout Type Edge, State

Slope Rising, Falling

Time Range 2 ns to 4.2 ns

Resolution 1 ns

Runt Trigger

Polarity +width, -width

Limit Range < , >, < >, > <

Time Range 2 ns to 4.2 ns

Resolution 1 ns

Pattern Trigger

Setting Invalid, Low, High

Logic AND, OR, NAND, NOR

Limit Range < , >, < >, > <

Time Range 2 ns to 4.2 ns

Resolution 1 ns